[1]朱继祥,雷 声,李帅,等.WC含量对铁基复合涂层组织与磨损性能的研究[J].南京师大学报(自然科学版),2021,44(01):28-34.[doi:10.3969/j.issn.1001-4616.2021.01.005]
 Zhu Jixiang,Lei Sheng,Li Shuai,et al.Research on the Microstructure and Wear Properties ofIron-Based Composite Coating with WC[J].Journal of Nanjing Normal University(Natural Science Edition),2021,44(01):28-34.[doi:10.3969/j.issn.1001-4616.2021.01.005]
点击复制

WC含量对铁基复合涂层组织与磨损性能的研究()
分享到:

《南京师大学报(自然科学版)》[ISSN:1001-4616/CN:32-1239/N]

卷:
第44卷
期数:
2021年01期
页码:
28-34
栏目:
·物理学·
出版日期:
2021-03-15

文章信息/Info

Title:
Research on the Microstructure and Wear Properties ofIron-Based Composite Coating with WC
文章编号:
1001-4616(2021)01-0028-07
作者:
朱继祥1雷 声12李帅1吴彦博1朱银锋1任悦3刘亚峰1许海丽1
(1.安徽建筑大学机械与电气工程学院,安徽 合肥 230601)(2.安徽省工程机械智能制造重点实验室,安徽 合肥 230601)(3.北京理工大学材料学院,北京 100081)
Author(s):
Zhu Jixiang1Lei Sheng12Li Shuai1Wu Yanbo1Zhu Yinfeng1Ren Yue3Liu Yafeng1Xu Haili1
(1.School of Mechanical and Electrical Engineering,Anhui Jianzhu University,Hefei 230601,China)(2.Key Laboratory of Intelligent Manufacturing of Construction Machinery of Anhui Province,Hefei 230601,China)(3.School of Materials Science and Engineering,Beijing Institute of Technology,Beijing 100081,China)
关键词:
激光熔覆磨损性能WC颗粒铁基合金微观组织
Keywords:
laser claddingwear performanceWC particlesFe-based alloymicrostructure
分类号:
TG148
DOI:
10.3969/j.issn.1001-4616.2021.01.005
文献标志码:
A
摘要:
为了解决导辊零部件表面易磨损失效问题,采用激光熔覆在GCR15轴承钢表面制备了不同WC含量铁基复合熔覆层. 分别通过SEM、EDS、XRD和磨损试验机对熔覆层微观组织、元素分布、物相组成和耐磨性能进行分析. 结果发现,WC的添加量对合金熔覆层组织及性能影响较大. 熔覆层与GCR15轴承钢基材冶金结合良好,熔覆层组织主要由胞状晶和等轴树枝晶组成,物相以Fe3W3C、Fe2W2C为主. 熔覆层平均显微硬度随WC含量的增加而增加,其中WC含量为质量分数50%的熔覆层平均显微硬度最高,约为基材的3倍. 在耐磨性能方面,磨损机理主要为磨料磨损和氧化磨损. 随着熔覆层WC质量分数的增加,磨损量先减小后变大,WC含量为质量分数30%的熔覆层耐磨性能最佳.
Abstract:
To solve the problem of serious wear and tear failure of guide roller parts,Fe-based composite cladding layers with different contents of WC were prepared for the surface of GCR15 bearing steel by laser cladding technology. The microstructure,element distribution,phase composition and wear resistance of the cladding layer were analyzed by SEM,EDS,XRD and wear tester. The results show that the addition of WC has an apparent influence on the microstructure and properties of the alloy cladding layer. The cladding layer has good metallurgical bonding with GCR15 bearing steel substrate. The microstructure of cladding layer is mainly composed of cellular crystals and equiaxed dendrites,and the main phase of it is Fe3W3C and Fe2W2C. Compared with the substrate,the average microhardness of the cladding layer increases obviously with the increase of WC content. When the content of WC is 50 wt.%,the average microhardness of cladding layer is the highest,which is about three times higher than that of GCR15 bearing steel substrate. In terms of wear resistance,the wear mechanism is mainly including abrasive wear and oxidation with the increase of WC mass fraction of cladding layer,the amount of wear decreases and then increases. The cladding layer with the 30 wt.% WC content has the best wear resistance.

参考文献/References:

[1] 张丽民,王书明,夏雯,等. 等离子熔覆技术在导辊上的应用[J]. 金属热处理,2010,35(4):21-23.
[2]邵春娟,米国发,许磊,等. 新型耐磨导卫板制备及性能分析[J]. 材料导报,2017,31(S2):380-384..
[3]张开源,尹延国,张国涛,等. 高能球磨-粉末冶金法制备硫化亚铁/铁基轴承材料的摩擦学性能[J]. 中国机械工程,2019,30(18):2172-2178.
[4]张航,路媛媛,王涛,等. 激光熔覆WC/H13-Inconel625复合材料的冲击韧性与磨损性能[J]. 材料工程,2019,47(4):127-134..
[5]AMADO J M,MONTERO J,TOBAR M J,et al. Laser cladding of Ni-WC layers with graded WC content[J]. Physics procedia,2014,56:269-275.
[6]王开明,雷永平,魏世忠,等. WC含量对激光熔覆Ni基WC复合涂层组织和性能的影响[J]. 材料热处理学报,2016,37(7):172-179.
[7]余畅,朱宇,简险峰,等. WC+Cr3C2增强铁基合金激光熔覆涂层磨损性能[J]. 金属热处理,2013,38(12):21-24.
[8]CHEN H Y,GU D D,KOSIBA K,et al. Achieving high strength and high ductility in WC-reinforced iron-based composites by laser additive manufacturing[J]. Additive manufacturing,2020,35:101195.
[9]王黎明,从善海,胡梅. WC增强Fe基复合材料的组织与性能研究[J]. 稀有金属与硬质合金,2015,43(5):22-29.
[10]CHEN W F,SHAN X,GUO Y,et al. The effect of reactive element species and concentrations on the isothermal oxidation of β-NiAl coating fabricated by spark plasma sintering[J]. Surface and coatings technology,2019,15:841-848.
[11]范鹏飞,孙文磊,张冠,等. 激光熔覆铁基合金梯度涂层的组织性能及应用[J]. 材料导报,2019,33(22):3806-3810.
[12]刘洪喜,董涛,张晓伟,等. 激光熔覆制备WC/Co50/Al硬质合金涂层刀具的微观结构及切削性能[J]. 中国激光,2017,44(8):104-112.
[13]ZHU Q,LEI Y C,CHEN X Z,et al. Microstructure and mechanical properties in TIG welding of CLAM steel[J]. Fusion engineering and design,2011,4-5(86):407-411.
[14]刘建弟,张述泉,王华明. 激光熔覆WC颗粒增强复合涂层的组织及耐磨性[J]. 中国有色金属学报,2012,22(9):2600-2607.
[15]LU J Z,CAO J,LU H F,et al. Wear properties and microstructural analyses of Fe-based coatings with various WC contents on H13 die steel by laser cladding [J]. Surface andcoatings technology,2019,369:228-237.



[16]LI W,XU P Q,WANG Y Y,et al. Laser synthesis and microstructure of micro- and nano-structured WC reinforced Co-based cladding layers on titanium alloy [J]. Journal of alloys and compounds,2018,749:10-22.

[17]王东生,田宗军. 激光熔覆NiCrBSi/WC-Co复合涂层的组织与耐磨性能[J]. 机械工程材料,2019,43(11):16-20.
[18]黄浩科,李祖来,山泉,等. 碳化钨/钢基复合材料的界面重熔[J]. 材料研究学报,2014,28(3):191-196.
[19]MUVVALA G,KARMAKAR D P,NATH A K. Monitoring and assessment of tungsten carbide wettability in laser cladded metal matrix composite coating using an IR pyrometer[J]. Journal of alloys and compounds,2017,714:514-521.
[20]熊中,王艳,徐强,等. WC对铁基合金喷焊层组织及磨损性能的影响[J]. 电焊机,2016,46(12):104-107.

备注/Memo

备注/Memo:
收稿日期:2020-07-03.
基金项目:国家自然科学基金项目(51877001)、 安徽省教育厅自然科学重点资助项目(kj2016A146)、 安徽建筑大学科研项目(横20180022、AJ-CXY-KF-17-38).
通讯作者:雷声,博士,教授,研究方向:材料成形技术. E-mail:leish1964@vip.126.com
更新日期/Last Update: 2021-03-15